Announcement

Collapse
No announcement yet.

Cisco 12406 router does not show interface 10g

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • Cisco 12406 router does not show interface 10g

    Hello,

    In the Cisco 12406 router, there is a SIP-601 card, 10 giga ports SPA card and a single card 10Giga

    #sho diags summary
    SLOT 0 (RP / LC 0): Modular SPA Interface Card (10G)
    SUBSLOT 0/0 (SPA-10X1GE-V2): 10-port Gigabit Ethernet Shared Port Adapter
    SUBSLOT 0/1 (SPA-1X10GE-L-V2): 1-port 10 Gigabit Ethernet Shared Port Adapter XFP based

    SPA Information:
    subslot 0/0: SPA-10X1GE-V2 (0x508 ), status is ok
    subslot 0/1: SPA-1X10GE-L-V2 (0x50C), status is ok


    When you run the "sho int des" command 10G interface is not displayed,

    #sho version

    System image file is "disk0: c12kprp-K4P-mz.120-32.SY10.bin"

    2 Route Processor Cards
    2 Clock Scheduler Cards
    3 Switch Fabric Cards
    12 Gigabit Ethernet / IEEE 802.3 interface (s)
    1 10GigabitEthernet / IEEE 802.3 interface (s) ---- here is

    The LED "ACTIVE / LINK" is off / off (Port is not enabled by software.)

    How to turn if the interface is not shown?

    I would appreciate the help you can give me.
    Last edited by biggles77; 8th March 2015, 04:04. Reason: Fix 8) smilie issue

  • #2
    Re: Cisco 12406 router does not show interface 10g

    No experience with that model myself, but on older model routers with switching module expansion cards in them, when you run a 'sh int status' command, you only see the switch ports. There are 2 internal routed ports which don't show in the status command. If you know the interface slot/module, and your post shows you do, try a 'show' command specific to the interface designation ('te1/0' as an example.)
    *RicklesP*
    MSCA (2003/XP), Security+, CCNA

    ** Remember: credit where credit is due, and reputation points as appropriate **

    Comment


    • #3
      Re: Cisco 12406 router does not show interface 10g

      RicklesP hi, thanks for answering

      commands output

      #sho int te0/1/0
      ^
      % Invalid input detected at '^' marker.

      #sho int ?
      Ethernet IEEE 802.3
      GigabitEthernet GigabitEthernet (IEEE 802.3z)
      Loopback Loopback interface
      Null Null interface
      accounting Show interface accounting
      crb Show interface routing/bridging info
      dampening Show interface dampening info
      description Show interface description
      fair-queue Show interface Weighted Fair Queueing (WFQ) info
      irb Show interface routing/bridging info
      load Show interface load info
      mac-accounting Show interface MAC accounting info
      mpls-exp Show interface MPLS experimental accounting info
      precedence Show interface precedence accounting info
      random-detect Show interface Weighted Random Early Detection (WRED) info
      rate-limit Show interface rate-limit info
      shape Show interface Traffic Shape info
      | Output modifiers
      <cr>

      Comment


      • #4
        Re: Cisco 12406 router does not show interface 10g

        OK. According to Cisco's own docs for the 12000-series device IOS XR releases, your command should probably look like this:
        'sho int TenGigE 0/1/0'

        If that doesn't give you anything, have a look at this link (all lines between the single quote marks are 1 URL):
        'http://www.cisco.com/c/en/us/td/docs/routers/xr12000/software/xr12k_r4-2/interfaces/command/reference/b_interfaces_cr42xr12k/b_interfaces_cr42xr12k_chapter_0100.html#wp2825553 440'

        This is their 'Ethernet Interface Commands on the Cisco IOS XR Software'. Pay particular attention to the 'Interface (Ehternet)' and 'show controllers (Ethernet)' sections. The '(Ethernet)' sections refer to all possible speeds, not just one.
        *RicklesP*
        MSCA (2003/XP), Security+, CCNA

        ** Remember: credit where credit is due, and reputation points as appropriate **

        Comment


        • #5
          Re: Cisco 12406 router does not show interface 10g

          Thanks RicklesP,
          Already found the solution, it is a problem with ios, which does not distinguish the gigaethernet interface with tengigaethernet

          The tengiga interface looks like this:
          GigabitEthernet0 / 1/0 is down, line protocol is down
          Hardware is GigMac 1 Port 10 Gigabit Ethernet, address is 0021.1c5a.bc10 (bia 0021.1c5a.bc10)
          MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec, rely 255/255, load 1/255
          Encapsulation ARPA, loopback not set
          Keepalive set (10 sec)
          Full Duplex, 10000Mbps, link type is force-up, media type is LR 1310nm

          Comment


          • #6
            Re: Cisco 12406 router does not show interface 10g

            Thanks for letting us know. This is the first time I've seen the newer IOS release, and it looks a bit confusing to me.
            *RicklesP*
            MSCA (2003/XP), Security+, CCNA

            ** Remember: credit where credit is due, and reputation points as appropriate **

            Comment

            Working...
            X