Announcement

Collapse
No announcement yet.

HP Procurve - cannot ping or get http access

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • HP Procurve - cannot ping or get http access

    Something must go right this week!

    Using http management > saving my browser session bombed out and now I cannot access my core switch.

    Gave it a few days, then power-cycled it but still no success

    I've connected via console and all the config looks fine (as it was) and can see from the menu that web management is enabled.

    HP ProCurve Switch 5308xl# show run

    interface C3
    name "Server1c"
    no lacp
    exit
    interface C4
    name "Server1d"
    no lacp
    exit
    interface C15
    name "Cab 6-2"
    no lacp
    exit
    interface D1
    name "Server2a"
    no lacp
    exit
    interface D2
    name "Server2b"
    no lacp
    exit
    interface D3
    name "Server2c"
    no lacp
    exit
    interface D4
    name "Server2d"
    no lacp
    exit
    interface D15
    name "Cab2-3"
    no lacp
    exit
    interface D16
    name "Cab 6-3"
    no lacp
    exit
    interface E1
    name "AVPN"
    exit
    interface E7
    name "HR Office"
    exit
    interface F11
    name "Raven"
    exit
    interface F18
    name "Cab 6 Wifi Link"
    exit
    interface G1
    name "Router"
    exit
    interface G8
    name "Guest Wireless VLAN"
    exit
    interface A1
    name "Cab2-1"
    no lacp
    exit
    interface B1
    name "Cab2-2"
    no lacp
    exit
    interface B3
    name "Cab 6-1"
    no lacp
    exit
    interface H18
    name "AidanG"
    exit
    interface H23
    name "DavidB"
    exit
    trunk C1-C4 Trk1 LACP
    trunk D1-D4 Trk2 LACP
    trunk A1,B1,D15 Trk3 LACP
    trunk B3,C15,D16 Trk4 LACP
    ip default-gateway 10.0.0.1
    snmp-server community "public" Unrestricted
    vlan 1
    name "DEFAULT_VLAN"
    ip address 10.0.0.32 255.255.255.0
    tagged F17,G16-G17
    no untagged A2-A4,B2,B4,C5-C14,C16,D5-D14,E1-E24,F1-F16,F18-F24,G1-G15,G18-G2
    4,H1-H24,Trk1-Trk4
    exit
    vlan 5
    name "GuestWifi"
    untagged G8
    tagged E21,F17,G16-G17,G22-G23,Trk3-Trk4
    exit
    vlan 6
    name "GuestWifi2"
    untagged F18
    tagged F17,G16-G17,G22-G23,Trk3-Trk4
    exit
    vlan 7
    name "MainWiFi"
    untagged A2-A4,B2,B4,C5-C14,C16,D5-D14,E1-E24,F1-F16,F19-F24,G1-G7,G9-G15,G18
    -G24,H1-H24,Trk1-Trk4
    tagged F17,G16-G17
    exit
    vlan 8
    name "VisitorWiFi"
    exit
    fault-finder bad-driver sensitivity high
    fault-finder bad-transceiver sensitivity high
    fault-finder bad-cable sensitivity high
    fault-finder too-long-cable sensitivity high
    fault-finder over-bandwidth sensitivity high
    fault-finder broadcast-storm sensitivity high
    fault-finder loss-of-link sensitivity high
    fault-finder duplex-mismatch-HDx sensitivity high
    fault-finder duplex-mismatch-FDx sensitivity high
    ip authorized-managers 10.0.0.96 255.255.255.0
    spanning-tree Trk1 priority 4
    spanning-tree Trk2 priority 4
    spanning-tree Trk3 priority 4
    spanning-tree Trk4 priority 4
    password manager

    HP ProCurve Switch 5308xl#

    I added the IP authorised manager for myself but nothing and I can ping everything apart from the switch (10.0.0.32)

    Any ideas/suggestions?

  • #2
    Factory Default it and start again? Sorry have only used Cisco switches and then had trouble reading the config files which were fairly simple.
    1 1 was a racehorse.
    2 2 was 1 2.
    1 1 1 1 race 1 day,
    2 2 1 1 2

    Comment


    • #3
      What port are you trying to connect from?

      Comment


      • #4
        Factory resetting is not an option for our live core switch, I just cannot ping or access using web management. I suspect it's default port is 80 for Web

        Comment


        • #5
          Originally posted by marcopolo
          I suspect it's default port is 80 for Web
          Have you downloaded and read the manual for this switch? It should tell you what the default port is.
          1 1 was a racehorse.
          2 2 was 1 2.
          1 1 1 1 race 1 day,
          2 2 1 1 2

          Comment


          • #6
            Again i'll ask. What physical port are you trying to connect from>?

            Comment


            • #7
              Originally posted by biggles77 View Post
              Have you downloaded and read the manual for this switch? It should tell you what the default port is.
              Yep, but only to see if I could figure out the current configuration as I've inherited this setup and cannot see that there is a default port. I've tried connecting to various ports that are tagged/untagged for vlans such as E22 and F17
              Last edited by marcopolo; 9th June 2015, 10:15.

              Comment


              • #8
                Can you untag a port and place it in the default VLAN

                Comment


                • #9
                  Originally posted by wullieb1 View Post
                  Can you untag a port and place it in the default VLAN
                  That one question triggered my thinking as to what it might be, I can now ping and gain web management access. I can see the problem, there's a batch of ports in another unused vlan that are untagged but they should be for the default_vlan. Looks as though I'm going to have to tag ports to one vlan, then untag the same ports for another vlan because It won't let me do a batch.

                  Thanks wullieb1

                  Comment

                  Working...
                  X