Announcement

Collapse
No announcement yet.

Help Joining Router to Network

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • Help Joining Router to Network

    Hi Guys,

    I need help to joining an Aztech WL830RT4 router to my existing home network. I already have my SBS2003 running as the DHCP server for my current network.

    I tried to put a fixed IP address into the LAN configuration page and disabled the DHCP in the router, though my laptop could connect to the router, but was not able to browse internet. Do i need to configure the WAN in the router as well? Please help me.

    Thanks in advance!
    Mind is like a parachute, it only works when it's open!

  • #2
    Re: Help Joining Router to Network

    Run the CEICW on SBS. Make sure the Router has an IP in the same range as your SBS network but NOT in the DHCP range. You should have created and Exclusion Range when you setup DHCP on SBS.
    1 1 was a racehorse.
    2 2 was 1 2.
    1 1 1 1 race 1 day,
    2 2 1 1 2

    Comment


    • #3
      Re: Help Joining Router to Network

      Your router (since it is ADSL) will need WAN settings configured -- your ISP will supply them
      You will also need to connect it to your phone line
      Tom Jones
      MCT, MCSE (2000:Security & 2003), MCSA:Security & Messaging, MCDBA, MCDST, MCITP(EA, EMA, SA, EDA, ES, CS), MCTS, MCP, Sec+
      PhD, MSc, FIAP, MIITT
      IT Trainer / Consultant
      Ossian Ltd
      Scotland

      ** Remember to give credit where credit is due and leave reputation points where appropriate **

      Comment


      • #4
        Re: Help Joining Router to Network

        Hello, i am sorry, my DHCP is actually running on SBS2000 and the CIECW command won't work in there. Could you please advise what command should i execute on SBS2000? The static IP that i assigned to the router is .19, while my DHCP range is from .201 ~ .254, i suppose it should be fine, right?
        Mind is like a parachute, it only works when it's open!

        Comment


        • #5
          Re: Help Joining Router to Network

          Post the full IP and subnet mask for both the router, server and DHCP please
          Tom Jones
          MCT, MCSE (2000:Security & 2003), MCSA:Security & Messaging, MCDBA, MCDST, MCITP(EA, EMA, SA, EDA, ES, CS), MCTS, MCP, Sec+
          PhD, MSc, FIAP, MIITT
          IT Trainer / Consultant
          Ossian Ltd
          Scotland

          ** Remember to give credit where credit is due and leave reputation points where appropriate **

          Comment


          • #6
            Re: Help Joining Router to Network

            Have you tried setting the ip on the router to x.x.x.1 and then configure your clients using the router as a default gateway to access the internet
            //Robert

            Comment


            • #7
              Re: Help Joining Router to Network

              Router:
              IP: 10.200.200.17
              Subnet: 255.255.255.0

              Server (DHCP):
              10.200.200.15 (Primary DNS)
              Subnet: 255.255.255.0
              Gateway: 10.200.200.254

              DHCP Range: 10.200.200.201 ~ .254
              Mind is like a parachute, it only works when it's open!

              Comment


              • #8
                Re: Help Joining Router to Network

                Your gateway should be the router's IP -- 10.200.200.17
                Tom Jones
                MCT, MCSE (2000:Security & 2003), MCSA:Security & Messaging, MCDBA, MCDST, MCITP(EA, EMA, SA, EDA, ES, CS), MCTS, MCP, Sec+
                PhD, MSc, FIAP, MIITT
                IT Trainer / Consultant
                Ossian Ltd
                Scotland

                ** Remember to give credit where credit is due and leave reputation points where appropriate **

                Comment


                • #9
                  Re: Help Joining Router to Network

                  Hi Ossian,

                  FYI. The gateway 10.200.200.254 is my Cisco firewall.
                  Mind is like a parachute, it only works when it's open!

                  Comment


                  • #10
                    Re: Help Joining Router to Network

                    Originally posted by ususim View Post
                    Hi Ossian,

                    FYI. The gateway 10.200.200.254 is my Cisco firewall.
                    Sorry, my psychic powers are off on Fridays Somehow I missed any mention of the Cisco device in any of the previous posts

                    Perhaps if you do a sketch of your network so we have more information we could give meaningful responses -- include all networking devices, servers and their IPs, and how they are interconnected.
                    Tom Jones
                    MCT, MCSE (2000:Security & 2003), MCSA:Security & Messaging, MCDBA, MCDST, MCITP(EA, EMA, SA, EDA, ES, CS), MCTS, MCP, Sec+
                    PhD, MSc, FIAP, MIITT
                    IT Trainer / Consultant
                    Ossian Ltd
                    Scotland

                    ** Remember to give credit where credit is due and leave reputation points where appropriate **

                    Comment


                    • #11
                      Re: Help Joining Router to Network

                      Too many typos and too little info.

                      Is it SBS 2000 or SBS 2003?
                      Is the Router IP .19 or .17?

                      Originally posted by Me
                      Run the CEICW on SBS.
                      Why do you want to run the Wizard on the Router? Read the quote, run the Wizard on the SBS Server.
                      CEICW = Configure E-Mail and Internet Connection Wizard
                      1 1 was a racehorse.
                      2 2 was 1 2.
                      1 1 1 1 race 1 day,
                      2 2 1 1 2

                      Comment

                      Working...
                      X