Announcement

Collapse
No announcement yet.

cisco router going cold start

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • cisco router going cold start

    dear all ,
    i am facing the issue when i start my cisco 1900 series router through console cable , its hung up and saying router going cold start , not able to type anything ,please help , i will paste the error below :
    System Bootstrap, Version 15.0(1r)M12, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2011 by cisco Systems, Inc.

    Total memory size = 512 MB - On-board = 512 MB, DIMM0 = 0 MB
    CISCO1941/K9 platform with 524288 Kbytes of main memory
    Main memory is configured to 64/-1(On-board/DIMM0) bit mode with ECC disabled


    Readonly ROMMON initialized
    program load complete, entry point: 0x80803000, size: 0x1b340
    program load complete, entry point: 0x80803000, size: 0x1b340


    IOS Image Load Test
    ___________________
    Digitally Signed Release Software
    program load complete, entry point: 0x81000000, size: 0x34d4d00
    Self decompressing the image : ################################################# ################################################## ############################## ################################################## ############################## ################################################## ############################## ######################### [OK]

    Smart Init is enabled
    smart init is sizing iomem
    TYPE MEMORY_REQ
    Onboard devices &
    buffer pools 0x01EF6000
    -----------------------------------------------
    TOTAL: 0x01EF6000

    Rounded IOMEM up to: 32Mb.
    Using 6 percent iomem. [32Mb/512Mb]

    Restricted Rights Legend

    Use, duplication, or disclosure by the Government is
    subject to restrictions as set forth in subparagraph
    (c) of the Commercial Computer Software - Restricted
    Rights clause at FAR sec. 52.227-19 and subparagraph
    (c) (1) (ii) of the Rights in Technical Data and Computer
    Software clause at DFARS sec. 252.227-7013.

    cisco Systems, Inc.
    170 West Tasman Drive
    San Jose, California 95134-1706



    Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.1(4)M2, REL EASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2011 by Cisco Systems, Inc.
    Compiled Mon 26-Sep-11 16:19 by prod_rel_team


    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.

    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

    If you require further assistance please contact us by sending email to
    [email protected].

    Cisco CISCO1941/K9 (revision 1.0) with 491520K/32768K bytes of memory.
    Processor board ID FCZ15449229
    2 Gigabit Ethernet interfaces
    1 terminal line
    DRAM configuration is 64 bits wide with parity disabled.
    255K bytes of non-volatile configuration memory.
    250880K bytes of ATA System CompactFlash 0 (Read/Write)



    Press RETURN to get started!


    Jan 2 12:00:02.395: %IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_LEVEL: Module name = c1900 Next reboot level = ipbasek9 and License = ipbasek9
    Mar 8 12:55:09.603: %IFMGR-7-NO_IFINDEX_FILE: Unable to open nvram:/ifIndex-tab le No such file or directory
    Mar 8 12:55:19.735: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to down
    Mar 8 12:55:19.735: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
    Mar 8 12:55:20.951: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthe rnet0/0, changed state to down
    Mar 8 12:55:20.951: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthe rnet0/1, changed state to down
    Mar 8 12:55:21.983: %SYS-5-CONFIG_I: Configured from memory by console
    Mar 8 12:55:23.943: %LINK-5-CHANGED: Interface Embedded-Service-Engine0/0, chan ged state to administratively down
    Mar 8 12:55:24.607: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.1(4)M2, REL EASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2011 by Cisco Systems, Inc.
    Compiled Mon 26-Sep-11 16:19 by prod_rel_team
    Mar 8 12:55:24.695: %SSH-5-ENABLED: SSH 1.99 has been enabled
    Mar 8 12:55:24.791: %SNMP-5-COLDSTART: SNMP agent on host Tamkean_Novotel is un dergoing a cold start
    Mar 8 12:55:25.403: %LINEPROTO-5-UPDOWN: Line protocol on Interface Embedded-Se rvice-Engine0/0, changed state to down

  • #2
    guys anyone please reply for the above issue

    Comment


    • #3
      Have you done any research on your own??

      From a 2 sec google search it would appear that the SNMP agent is restarting due to a restart of the router.

      Comment


      • #4
        yes but , i did not get the proper answer , if you suggest me any link i will go through that

        Comment


        • #5
          What answer did you get, and how is it not a "proper" answer?
          Suggested link: www.google.com (other search engines are available)
          Tom Jones
          MCT, MCSE (2000:Security & 2003), MCSA:Security & Messaging, MCDBA, MCDST, MCITP(EA, EMA, SA, EDA, ES, CS), MCTS, MCP, Sec+
          PhD, MSc, FIAP, MIITT
          IT Trainer / Consultant
          Ossian Ltd
          Scotland

          ** Remember to give credit where credit is due and leave reputation points where appropriate **

          Comment


          • #6
            Maybe i should start charging for my time???

            https://supportforums.cisco.com/disc...t-does-it-mean

            Comment


            • #7
              The error statement calls out a missing file/directory--probably a faulty NVRAM module. Has there been any overheats or power spikes? Or has a config change been made recently?
              *RicklesP*
              MSCA (2003/XP), Security+, CCNA

              ** Remember: credit where credit is due, and reputation points as appropriate **

              Comment

              Working...
              X