Announcement

Collapse
No announcement yet.

AIRONET 1131AG no config t command

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • AIRONET 1131AG no config t command

    Good Morning everyone,
    I have recently purchased a used AIRONET 1131AG and using the cisco manaual I reset it to factory restore. I am able to connect via the console, however I can not for the life of me figure out how to make configuration changes to this device because there does not seem to be a config t command available.

    I can access privileged mode and when I do "?" I dont even see configure as an option. Any advise would really be appreciated.

  • #2
    Re: AIRONET 1131AG no config t command

    What do you see then?
    Marcel
    Technical Consultant
    Netherlands
    http://www.phetios.com
    http://blog.nessus.nl

    MCITP(EA, SA), MCSA/E 2003:Security, CCNA, SNAF, DCUCI, CCSA/E/E+ (R60), VCP4/5, NCDA, NCIE - SAN, NCIE - BR, EMCPE
    "No matter how secure, there is always the human factor."

    "Enjoy life today, tomorrow may never come."
    "If you're going through hell, keep going. ~Winston Churchill"

    Comment


    • #3
      Re: AIRONET 1131AG no config t command

      I do "?" i see the following:



      Code:
         AP001b.d53a.6da4#?
        Exec commands:
          cd               Change current directory
          clear            Reset functions
          clock            Manage the system clock
          crypto           Encryption related commands.
          debug            Debugging functions (see also 'undebug')
          delete           Delete a file
          dir              List files on a filesystem
          disable          Turn off privileged commands
          enable           Turn on privileged commands
          exit             Exit from the EXEC
          fsck             Fsck a filesystem
          help             Description of the interactive help system
          led              LED functions
          lock             Lock the terminal
          login            Log in as a particular user
          logout           Exit from the EXEC
          lwapp            lwapp exec commands
          mkdir            Create new directory
          more             Display the contents of a file  
        name-connection  Name an existing network connection
          no               Disable debugging functions
          ping             Send echo messages
          pwd              Display current working directory
          release          Release a resource
          reload           Halt and perform a cold restart
          rename           Rename a file
          renew            Renew a resource
          rmdir            Remove existing directory
          save             Start to save raise_interrupt_level stack
          send             Send a message to other tty lines
          set              Set system parameter (not config)
          show             Show running system information
          systat           Display information about terminal lines
          terminal         Set terminal line parameters
          test             Test subsystems, memory, and interfaces
          traceroute       Trace route to destination
          undebug          Disable debugging functions (see also 'debug')
          upgrade          Upgrade software
          verify           Verify a file

      Comment


      • #4
        Re: AIRONET 1131AG no config t command

        It looks like you haven't enter the privileged mode (enable command)
        however, can you do a show flash: ?
        Marcel
        Technical Consultant
        Netherlands
        http://www.phetios.com
        http://blog.nessus.nl

        MCITP(EA, SA), MCSA/E 2003:Security, CCNA, SNAF, DCUCI, CCSA/E/E+ (R60), VCP4/5, NCDA, NCIE - SAN, NCIE - BR, EMCPE
        "No matter how secure, there is always the human factor."

        "Enjoy life today, tomorrow may never come."
        "If you're going through hell, keep going. ~Winston Churchill"

        Comment


        • #5
          Re: AIRONET 1131AG no config t command

          Based on the output above, it appears the AP is running a LWAPP image, not an autonomous mode image.

          The following link should help

          Converting a Lightweight Access Point Back to Autonomous Mode

          Comment


          • #6
            Re: AIRONET 1131AG no config t command

            Thanks for that link, It really helped. I was able to find the correct ios and I am going to take a shot at re-imaging the 1131

            Comment


            • #7
              Re: AIRONET 1131AG no config t command

              Re-image was a success, I am now running the ap ios rather then the lap version.
              I can now use the commandline to configure the ap and was also able to access the web interface.

              Thank you very much for the link and advice.

              Comment


              • #8
                Re: AIRONET 1131AG no config t command

                Glad to hear the conversion to autonomous mode was successful

                Comment

                Working...
                X