Announcement

Collapse
No announcement yet.

Cisco 871W don't enter in Roomon mode...

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • Cisco 871W don't enter in Roomon mode...

    Hi, I have a cisco's 871W router. When I connect it by CLI interface (with RS232 cable), the IOS dont't start:

    ;----------------------------------------------
    System Bootstrap, Version 12.3(8r)YI2, RELEASE SOFTWARE
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2005 by cisco Systems, Inc.

    C870 series (Board ID: 3-14 platform with 131072 Kbytes of main memory

    Booting flash:/c870-advsecurityk9-mz.124-4.T3.bin
    Self decompressing the image : #################################################
    ######################### [OK]

    Restricted Rights Legend

    Use, duplication, or disclosure by the Government is
    subject to restrictions as set forth in subparagraph
    (c) of the Commercial Computer Software - Restricted
    Rights clause at FAR sec. 52.227-19 and subparagraph
    (c) (1) (ii) of the Rights in Technical Data and Computer
    Software clause at DFARS sec. 252.227-7013.

    cisco Systems, Inc.
    170 West Tasman Drive
    San Jose, California 95134-1706



    Cisco IOS Software, C870 Software (C870-ADVSECURITYK9-M), Version 12.4(4)T3, REL
    EASE SOFTWARE (fc3)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2006 by Cisco Systems, Inc.
    Compiled Mon 22-May-06 20:10 by kellythw
    Image text-base: 0x8002008C, data-base: 0x813F5BF0


    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.

    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

    If you require further assistance please contact us by sending email to
    [email protected].

    Cisco 871W (MPC8272) processor (revision 0x200) with 118784K/12288K bytes of mem
    ory.
    Processor board ID FCZ102222D4
    MPC8272 CPU Rev: Part Number 0xC, Mask Number 0x10
    5 FastEthernet interfaces
    1 802.11 Radio
    128K bytes of non-volatile configuration memory.
    24576K bytes of processor board System flash (Intel Strataflash)
    File ../crypto/ssl/src/ssltrspt.c; Line 345 # Assert failed: 'rec->sent == rec->
    data.length'
    File ../crypto/ssl/src/ssltrspt.c; Line 346 # Assert failed: 'err == 0'
    File ../crypto/ssl/src/sslalert.c; Line 124 # Assert failed: 'ctx->protocolVersi
    on == SSL_Version_3_0'
    File ../crypto/ssl/src/ssltrspt.c; Line 345 # Assert failed: 'rec->sent == rec->
    data.length'
    File ../crypto/ssl/src/ssltrspt.c; Line 346 # Assert failed: 'err == 0'
    File ../crypto/ssl/src/sslalert.c; Line 124 # Assert failed: 'ctx->protoc

    ;---------------------------------------------------------

    If I break the boot sequence, (pressing Ctrl+Break on Hyperterminal)the router restarts but don't enter in bootmode, it repeats the same information... I don't have any interface where I can write any command... I have the Rom and IOS files but I can't update it without write any command, right? What I should do?

  • #2
    Re: Cisco 871W don't enter in Roomon mode...

    you need to access the router then write this commands:

    conf t
    config-register 0x0
    exit
    wr
    reload


    once you reload the router it would auto start in rommon.

    hope it helps you.

    Comment


    • #3
      Re: Cisco 871W don't enter in Roomon mode...

      But the problem is that I can not insert any command because the break restarts the Router and if start sequences continues, the router will fail on IOS load (like I write before)

      I need update the files or have access to any interface where I can write commands This is my problem...

      Thanks kbendala, if you know other form to enter in CLI and type commands, say it.


      Sorry, I'm Portuguese and my English is a little bad

      Comment

      Working...
      X