Announcement

Collapse
No announcement yet.

how can I configer cisco switch 2950

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • how can I configer cisco switch 2950

    when I reset switch I can not config the switch 2950




    Code:
     
    C2950 Boot Loader (C2950-HBOOT-M) Version 12.1(11r)EA1, RELEASE SOFTWARE (fc1)
    Compiled Mon 22-Jul-02 17:18 by antonino
    WS-C2950SX-24 starting...
    Base ethernet MAC Address: 00:18:b4:04:ed:80
    Xmodem file system is available.
    
    The system has been interrupted prior to initializing the
    flash filesystem.  The following commands will initialize
    the flash filesystem, and finish loading the operating
    system software:
    
        flash_init
        load_helper
        boot
     
    switch: conf t
    Unknown cmd: conf
    switch: writ erase
    Unknown cmd: writ
    switch:       :
    switch: cmd:
    switch: wrire erase
    Unknown cmd: wrire
    switch: write erase
    Unknown cmd: write
    switch:

    how can I config cisco switch 2950 another time ?
    Last edited by maaaajed; 15th April 2009, 11:24.

  • #2
    Re: how can I configer cisco switch 2950

    Simply type ? to see what your options are?

    first of all you need to go into enable mode before you can use the conf t command.
    However I'm not sure if the switch is fully booted so that's why I say; type the ? first.
    Marcel
    Technical Consultant
    Netherlands
    http://www.phetios.com
    http://blog.nessus.nl

    MCITP(EA, SA), MCSA/E 2003:Security, CCNA, SNAF, DCUCI, CCSA/E/E+ (R60), VCP4/5, NCDA, NCIE - SAN, NCIE - BR, EMCPE
    "No matter how secure, there is always the human factor."

    "Enjoy life today, tomorrow may never come."
    "If you're going through hell, keep going. ~Winston Churchill"

    Comment


    • #3
      how can I configer cisco switch 2950 still reload

      still reload

      Code:
      reload>?
      Exec commands:
        access-enable    Create a temporary Access-List entry
        clear            Reset functions
        connect          Open a terminal connection
        disable          Turn off privileged commands
        disconnect       Disconnect an existing network connection
        enable           Turn on privileged commands
        exit             Exit from the EXEC
        help             Description of the interactive help system
        lock             Lock the terminal
        login            Log in as a particular user
        logout           Exit from the EXEC
        name-connection  Name an existing network connection
        ping             Send echo messages
        rcommand         Run command on remote switch
        resume           Resume an active network connection
        set              Set system parameter (not config)
        show             Show running system information
        ssh              Open a secure shell client connection
        systat           Display information about terminal lines
        telnet           Open a telnet connection
        terminal         Set terminal line parameters
        traceroute       Trace route to destination
        tunnel           Open a tunnel connection
        where            List active connections
      
      reload>
      reload>exit
      
      
      
      reload con0 is now available
      answer me please !

      Comment


      • #4
        Re: how can I configer cisco switch 2950 still reload

        Oh reload is the hostname.

        type the following:

        Enable
        conf t
        Hostname <whatever you want>
        end
        wr mem
        Marcel
        Technical Consultant
        Netherlands
        http://www.phetios.com
        http://blog.nessus.nl

        MCITP(EA, SA), MCSA/E 2003:Security, CCNA, SNAF, DCUCI, CCSA/E/E+ (R60), VCP4/5, NCDA, NCIE - SAN, NCIE - BR, EMCPE
        "No matter how secure, there is always the human factor."

        "Enjoy life today, tomorrow may never come."
        "If you're going through hell, keep going. ~Winston Churchill"

        Comment


        • #5
          another problem

          thanks alot

          but when I type

          Enable

          show me
          Code:
           
          password:
          password:
          password:
           
          % bad secret
           
          reload

          please help me

          Comment


          • #6
            Re: another problem

            You have to know the enable password.
            if you don't know it, you have to crack it.

            http://www.cisco.com/en/US/products/...80094184.shtml
            Marcel
            Technical Consultant
            Netherlands
            http://www.phetios.com
            http://blog.nessus.nl

            MCITP(EA, SA), MCSA/E 2003:Security, CCNA, SNAF, DCUCI, CCSA/E/E+ (R60), VCP4/5, NCDA, NCIE - SAN, NCIE - BR, EMCPE
            "No matter how secure, there is always the human factor."

            "Enjoy life today, tomorrow may never come."
            "If you're going through hell, keep going. ~Winston Churchill"

            Comment


            • #7
              Re: how can I configer cisco switch 2950

              C2950 Boot Loader (C2950-HBOOT-M) Version 12.1(11r)EA1, RELEASE SOFTWARE (fc1)
              Compiled Mon 22-Jul-02 17:18 by antonino
              WS-C2950SX-24 starting...
              Base ethernet MAC Address: 00:18:b4:04:ed:80
              Xmodem file system is available.

              The system has been interrupted prior to initializing the
              flash filesystem. The following commands will initialize
              the flash filesystem, and finish loading the operating
              system software:

              flash_init
              load_helper
              boot

              switch: conf t
              Unknown cmd: conf
              switch: writ erase
              Unknown cmd: writ
              switch: :
              switch: cmd:
              switch: wrire erase
              Unknown cmd: wrire
              switch: write erase
              Unknown cmd: write
              switch:


              Dear if you are seeing "switch: " it means you are still in ROMMON MODE and you need to break password .

              Just follow steps one by one as i am writing .It is very simple .

              Step 1-unplug the power cable from your switch and plug it again while plugging it press MODE button till you reach ROMMON mode which is almost in left hand side of your switch .
              Step 2-Type command Flash_init.and press ENTER.

              Step 3-Type command Load_helper and press ENTER.
              Step 4-Type rename flash:config.text flash:config.backup and press ENTER.

              Step 5-Type Boot and press ENTER.

              Step 6- It will Boot .Afte the it will ask for intial configuration then you have to write No and press ENTER.

              Step 7-You will see Switch> like this now write en and press ENTER.

              Step 8- Now your password has been break and now you are ready to use your switch.

              For more explanation please refer Mr.Dumber doc which he already forwarded.



              Cheers
              DT

              Comment

              Working...
              X