Announcement

Collapse
No announcement yet.

Cisco Router config routing problem

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • Cisco Router config routing problem

    Hello Everyone
    I hope someone can help me with this.
    Everything i have in the config is correct to the best
    of my limited knowledge, but for the liofe of me I cannot get
    out to the internet with this.
    Not getting DNS. I have a sneaky suspicion it is my access-list
    and have tried different orders but to date nothing has worked.
    I also wonder if my overload statement is correct

    hostname WP2621
    !
    boot-start-marker
    boot-end-marker
    no aaa new-model
    resource policy
    ip cef
    !
    no ip dhcp use vrf connected
    ip dhcp excluded-address 192.168.0.2 192.168.0.101
    ip dhcp excluded-address 192.168.0.249 192.168.0.254
    !
    ip dhcp pool whitepine
    network 192.168.0.0 255.255.255.0
    default-router 192.168.0.101
    dns-server 192.168.0.101
    domain-name seg.net
    !
    ip name-server 206.34.181.15 (These are seg.net)
    ip name-server 206.34.181.16
    ip name-server 69.24.0.2 (These are my ISP)
    ip name-server 69.24.8.2
    !
    interface ATM0/0
    no ip address
    shutdown
    no atm ilmi-keepalive
    dsl operating-mode auto
    !
    interface FastEthernet0/0
    ip address dhcp
    ip access-group 101 out
    ip nat outside
    ip virtual-reassembly
    duplex auto
    speed auto
    !
    interface FastEthernet0/1
    ip address 192.168.0.101 255.255.255.0
    ip nat inside
    ip virtual-reassembly
    speed 100
    full-duplex
    no mop enabled
    !
    ip route 0.0.0.0 0.0.0.0 216.107.xxx.0
    !
    no ip http server
    no ip http secure-server
    ip nat inside source list 101 interface FastEthernet0/0 overload
    !
    access-list 101 permit tcp 192.168.0.0 0.0.0.255 any
    access-list 101 permit tcp any any established
    access-list 101 permit udp any eq domain any
    access-list 101 permit tcp any any eq www
    access-list 101 permit tcp any any eq 22
    access-list 101 permit tcp any any eq telnet
    access-list 101 permit tcp any any eq pop3
    access-list 101 permit tcp any any eq smtp
    access-list 101 deny ip any any

    sh ip rou
    Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
    D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
    N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
    E1 - OSPF external type 1, E2 - OSPF external type 2
    i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
    ia - IS-IS inter area, * - candidate default, U - per-user static route
    o - ODR, P - periodic downloaded static route
    Gateway of last resort is 216.107.224.0 to network 0.0.0.0
    C 192.168.0.0/24 is directly connected, FastEthernet0/1
    S* 0.0.0.0/0 [1/0] via 216.107.xxx.0
    C 216.107.xxx.0/23 is directly connected, FastEthernet0/0

    Output of debug IP packet

    : tableid=0, s=192.168.0.101 (local), d=192.168.0.104 (FastEthernet0/1), route
    : s=216.107.224.1 (FastEthernet0/0), d=255.255.255.255, len 328, rcvd 2
    : tableid=0, s=192.168.0.101 (local), d=192.168.0.104 (FastEthernet0/1), route
    : s=216.107.224.1 (FastEthernet0/0), d=255.255.255.255, len 328, rcvd 2

    Any help would be very much appreciated!!!
    Thanks
    Greg Worcester

  • #2
    Re: Cisco Router config routing problem

    First line of access list I think should be somethink like this :
    access-list 101 permit ip 192.168.0.0 0.0.0.255 any

    Comment


    • #3
      Re: Cisco Router config routing problem

      First remove the access-list from the outside interface. Then see if you can get out. If you can, then you know its your access-list. Now you can start tweaking it.
      CCNA, Network+

      Comment

      Working...
      X