Announcement

Collapse
No announcement yet.

Cisco 2801 Router - Can' t see the interface

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • Cisco 2801 Router - Can' t see the interface

    Hello,

    I'm new to this router stuff. When I boot the router and log into it and enter the command "sh run". I'm missing the f0/0 and f0/1 interfaces. Any idea how to get this to show up. If I look into the "sdmconfig-2801.cfg" file the interfaces are there.

    System Bootstrap, Version 12.3(8r)T9, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 2004 by cisco Systems, Inc.
    PLD version 0x10
    GIO ASIC version 0x127
    c2801 processor with 262144 Kbytes of main memory
    Main memory is configured to 64 bit mode with parity disabled

    Readonly ROMMON initialized
    program load complete, entry point: 0x8000f000, size: 0xc100
    Initializing ATA monitor library.......
    program load complete, entry point: 0x8000f000, size: 0xc100
    Initializing ATA monitor library.......
    program load complete, entry point: 0x8000f000, size: 0x13552f4
    Self decompressing the image : ################################################## ################################################## ################################################## ################################################## ##################### [OK]
    Smart Init is enabled
    smart init is sizing iomem
    ID MEMORY_REQ TYPE
    Unable to read eeprom
    Unable to read eeprom
    0X003AA110 public buffer pools
    0X00211000 public particle pools
    0X00020000 Crypto module pools
    0X00120000 VPM buffer pools
    0X0052 0X0001A800 Card in slot 2
    0X0052 0X0001A800 Card in slot 3
    If any of the above Memory Requirements are
    "UNKNOWN", you may be using an unsupported
    configuration or there is a software problem and
    system operation may be compromised.
    Allocating additional 18659954 bytes to IO Memory.
    PMem allocated: 240123904 bytes; IOMem allocated: 28311552 bytes
    Restricted Rights Legend
    Use, duplication, or disclosure by the Government is
    subject to restrictions as set forth in subparagraph
    (c) of the Commercial Computer Software - Restricted
    Rights clause at FAR sec. 52.227-19 and subparagraph
    (c) (1) (ii) of the Rights in Technical Data and Computer
    Software clause at DFARS sec. 252.227-7013.
    cisco Systems, Inc.
    170 West Tasman Drive
    San Jose, California 95134-1706

    Cisco IOS Software, 2801 Software (C2801-SPSERVICESK9-M), Version 12.3(11)T8, RELEASE SOFTWARE (fc3)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2005 by Cisco Systems, Inc.
    Compiled Thu 06-Oct-05 00:46 by kehsiao
    Image text-base: 0x600741FC, data-base: 0x62100000

    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.
    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
    If you require further assistance please contact us by sending email to
    [email protected].
    Cisco 2801 (revision 0.0) with 234496K/27648K bytes of memory.
    Processor board ID
    DRAM configuration is 64 bits wide with parity disabled.
    191K bytes of NVRAM.
    62720K bytes of ATA CompactFlash (Read/Write)

    Press RETURN to get started!

    test#sh run
    Building configuration...
    Current configuration : 546 bytes
    !
    version 12.3
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    no service dhcp
    !
    hostname test
    !
    boot-start-marker
    boot system flash
    boot-end-marker
    !
    !
    mmi polling-interval 60
    no mmi auto-configure
    no mmi pvc
    mmi snmp-timeout 180
    no aaa new-model
    ip subnet-zero
    ip cef
    !
    !
    !
    !
    no ftp-server write-enable
    !
    !
    !
    !
    !
    !
    !
    !
    !
    !
    !
    !
    !
    !
    !
    !
    !
    !
    ip classless
    !
    !
    no ip http server
    no ip http secure-server
    !
    !
    !
    !
    control-plane
    !
    !
    !
    !
    !
    !
    !
    line con 0
    line aux 0
    line vty 0 4
    login
    !
    end
    test#dir
    Directory of flash:/
    1 -rw- 20272276 Nov 03 2005 14:44:34 +00:00 c2801-spservicesk9-mz.123-11.T8.bin
    2 -rw- 1644 Nov 03 2005 15:02:22 +00:00 sdmconfig-2801.cfg
    3 -rw- 4052480 Nov 03 2005 15:02:52 +00:00 sdm.tar
    4 -rw- 812032 Nov 03 2005 15:03:12 +00:00 es.tar
    5 -rw- 1007616 Nov 03 2005 15:03:36 +00:00 common.tar
    6 -rw- 1038 Nov 03 2005 15:03:54 +00:00 home.shtml
    7 -rw- 113152 Nov 03 2005 15:04:12 +00:00 home.tar
    8 -rw- 511939 Nov 03 2005 15:04:34 +00:00 128MB.sdf

  • #2
    Re: Cisco 2801 Router - Can' t see the interface

    First confirm me that are you able to see both interfaces physically in router .

    Second thing is post "sh Diag" output



    Cheers
    DT

    Comment

    Working...
    X