Announcement

Collapse
No announcement yet.

Exchange 2007 Send Error Message

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • Exchange 2007 Send Error Message

    Diagnostic information for administrators:

    Generating server: SPDC-01.spmld114.dyndns.biz

    [email protected]
    #550 5.1.1 RESOLVER.ADR.RecipNotFound; not found ##

    Original message headers:

    Received: from SPDC-01.spmld114.dyndns.biz ([10.0.0.100]) by
    SPDC-01.spmld114.dyndns.biz ([10.0.0.100]) with mapi; Thu, 19 May 2011
    19:32:25 -0400
    Content-Type: application/ms-tnef; name="winmail.dat"
    Content-Transfer-Encoding: binary
    From: Brent Smith <[email protected]>
    To: "[email protected]" <[email protected]>
    Date: Thu, 19 May 2011 19:32:23 -0400
    Subject: Test
    Thread-Topic: Test
    Thread-Index: AQHMFn0BNW8DiWJPYkaifZaTQ0j4ZA==
    Message-ID: <[email protected].biz>
    Accept-Language: en-US
    Content-Language: en-US
    X-MS-Has-Attach:
    X-MS-TNEF-Correlator: <[email protected].biz>
    MIME-Version: 1.0







    This is the error message. I can't send to any email address outside of my organization

  • #2
    Re: Exchange 2007 Send Error Message

    Did you create a Send Connector? Exchange doesn't create one on its own. Has it ever worked?

    Simon.
    --
    Simon Butler
    Exchange MVP

    Blog: http://blog.sembee.co.uk/
    More Exchange Content: http://exchange.sembee.info/
    Exchange Resources List: http://exbpa.com/
    In the UK? Hire me: http://www.sembee.co.uk/

    Sembee is a registered trademark, used here with permission.

    Comment


    • #3
      Re: Exchange 2007 Send Error Message

      It has never worked sending email outside my organization.

      The guide I used to set up the connector is on the Petri website.


      Name is External Connector, type is internet, access is * and include all subdomains is checked.

      Thanks -bsmith

      Comment


      • #4
        Re: Exchange 2007 Send Error Message

        If it has never worked, have you verified that you can access remote SMTP servers? It could be that your firewall isn't configured correctly or your ISP is blocking port 25.

        telnet maila.microsoft.com 25

        Should get you a response. If the cursor just sits there, then the port is being blocked.

        Simon.
        --
        Simon Butler
        Exchange MVP

        Blog: http://blog.sembee.co.uk/
        More Exchange Content: http://exchange.sembee.info/
        Exchange Resources List: http://exbpa.com/
        In the UK? Hire me: http://www.sembee.co.uk/

        Sembee is a registered trademark, used here with permission.

        Comment


        • #5
          Re: Exchange 2007 Send Error Message

          This is the reply I get from the telnet command:

          220 mail04.microsoft.com Microsoft ESMTP MAIL Service ready at Fri, 20 May 2011 13:34:37 -0700

          451 4.7.0 Timeout waiting for client input

          Connection to host lost.

          Comment


          • #6
            Re: Exchange 2007 Send Error Message

            In that case you should be able to send email out to other hosts - if the Exchange server is configured correctly.

            That means a correctly configured Send Connector and Accepted Domain.

            Simon.
            --
            Simon Butler
            Exchange MVP

            Blog: http://blog.sembee.co.uk/
            More Exchange Content: http://exchange.sembee.info/
            Exchange Resources List: http://exbpa.com/
            In the UK? Hire me: http://www.sembee.co.uk/

            Sembee is a registered trademark, used here with permission.

            Comment


            • #7
              Re: Exchange 2007 Send Error Message

              I followed correct procedure for send connectors and accepted domains. I have gmail.com, yahoo.com, aol.com, sc.rr.com, etc put in under accepted domains.

              No receive connectors though (if they even exist)

              Comment


              • #8
                Re: Exchange 2007 Send Error Message

                That is not correct and is the cause of your problems.

                Why have you listed those domains in your Accepted Domains list?
                That has basically told Exchange that your server is responsible for all of those domains. You should only have your own domain listed in the Accepted domains list.

                Simon.
                --
                Simon Butler
                Exchange MVP

                Blog: http://blog.sembee.co.uk/
                More Exchange Content: http://exchange.sembee.info/
                Exchange Resources List: http://exbpa.com/
                In the UK? Hire me: http://www.sembee.co.uk/

                Sembee is a registered trademark, used here with permission.

                Comment


                • #9
                  Re: Exchange 2007 Send Error Message

                  I was told by someone I know that is the head of IT at a huge business. I guess he was wrong huh..

                  I will delete those and try again.

                  Now, Sembee, the error is that my messages cant be delivered because of security policies. mx.google.com rejected my message.

                  The IP I am using is not authorized to 550-5.7.1 send email directly to our servers. Please use the SMTP relay at your 550-5.7.1 service provider.



                  Any ideas on this error?
                  Last edited by bsmith; 21st May 2011, 04:39.

                  Comment


                  • #10
                    Re: Exchange 2007 Send Error Message

                    The error means what it says. Google will not accept email directly from your server. Many reasons for that, none of which are Exchange related. Dynamic IP address, lack of PTR, residential IP address etc. Set the Send Connector to route email via your ISPs SMTP server - which is set as a smart host.

                    Head of IT at a large company? Probably a pen pusher rather than a techie. I have seen too many heads of IT who wouldn't know one end of a hard disk from another. The information was so wrong they don't know what they are on about.

                    Simon.
                    --
                    Simon Butler
                    Exchange MVP

                    Blog: http://blog.sembee.co.uk/
                    More Exchange Content: http://exchange.sembee.info/
                    Exchange Resources List: http://exbpa.com/
                    In the UK? Hire me: http://www.sembee.co.uk/

                    Sembee is a registered trademark, used here with permission.

                    Comment


                    • #11
                      Re: Exchange 2007 Send Error Message

                      Now I can send email anywhere to anyone. Thanks.

                      But now I can't send email to organization. (from gmail to my organization). Or any other web mail provider.

                      And also the permissions for my website got messed up or something. I can access my OWA logon page but when I logon I get a 403 error and that I cannot access that directory.

                      This little project of mine is turning out to be a headache.
                      Last edited by bsmith; 21st May 2011, 20:09.

                      Comment


                      • #12
                        Re: Exchange 2007 Send Error Message

                        Do you have your DNS setup correctly? Port 25 open on the firewall? Does your ISP allow inbound port 25 traffic?

                        Simon.
                        --
                        Simon Butler
                        Exchange MVP

                        Blog: http://blog.sembee.co.uk/
                        More Exchange Content: http://exchange.sembee.info/
                        Exchange Resources List: http://exbpa.com/
                        In the UK? Hire me: http://www.sembee.co.uk/

                        Sembee is a registered trademark, used here with permission.

                        Comment


                        • #13
                          Re: Exchange 2007 Send Error Message

                          DNS is set up okay, Firewall is turned off completely, and my ISP for sure does not block incoming/outgoing traffic on port 25. I still cannot receive mail. And I also have receive connectors set up to receive external mail. Hmmm.

                          Comment


                          • #14
                            Re: Exchange 2007 Send Error Message

                            what diagnostic codes do you get when you attempt to send yourself email?
                            Please do show your appreciation to those who assist you by leaving Rep Point https://www.petri.com/forums/core/im.../icon_beer.gif

                            Comment


                            • #15
                              Re: Exchange 2007 Send Error Message

                              I get no error message when I send email from me to me withing my exchange organization. Also, other members in my organization can send mail to me. Its just when a gmail account, or yahoo account, etc sends email to anyone in my organization where I don't get the mail. I don't believe any error codes are returned to either address, I just never receive the mail.

                              Whenever I send and email from my yahoo account to my organization account, I get a reply into my yahoo account from a MAILERAEMON. This email goes automatically into the spam box.

                              When I send and email from my gmail to my organization account, I get a reply to my gmail that it will try to resend the message 3 more times and after that the message will fail to send

                              Im almost certain the problem is with my mx record. Even though I have one setup in DNS, i think i need to call my isp so they can set one up to my ip and domain name. I have narrowed the problem down to that but if anyone has other thoughts or agrees with me, please let me know so I can go ahead and call my ISP.

                              Thanks.
                              Last edited by bsmith; 25th May 2011, 02:33.

                              Comment

                              Working...
                              X